ISO. Second edition. Reference number Permission can be requested from either ISO at the address below or ISO’s member body in the. 31 Jul Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. EN ISO Intravascular catheters – Sterile and single-use catheters – Part 5 : Over-needle peripheral catheters – ISO specifies requirements.
|Published (Last):||12 April 2013|
|PDF File Size:||9.43 Mb|
|ePub File Size:||6.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
The iso 10555-5 tube may have a single lumen or multiple lumens. I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically or gravimetrically.
BS EN ISO 10555-5:2013
Iso 10555-5 BIS has the copyright of all its publications. Assembly comprising iso 10555-5 cath- eter tube, catheter hub and any integral fittings.
Search the history of ieo billion web pages on the Internet. The corresponding Indian Standards which are to be substituted iso 10555-5 their iao are listed below along with their degree iso 10555-5 equivalence for the editions indicated: Other parts of this standard are as follows: NOTE 3 The point should be designed to be noncoring.
I Principle A force is applied successively tensile and connpress- ive to the needle tube and needle hub and the tube- hub union is then examined for loosening. International Standard ISO Suggested colour references for opaque naaterials are given in annex C.
Standards are also reviewed periodically; a standard alongwith amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. E-5 Test report The test report shall contain at least the following information: An approved test method for producing a value of radio-detectability will be established. Add the following iiso Attention is particularly drawn to the following: When the needle is fully izo into the catheter unit, the catheter tube shall iso 10555-5 extend beyond the heel of the needle bevel nor be nnore than 1 nnnn fronn it see dinnension a in figure 1.
The number of significant places retained in iso 10555-5 rounded off value 110555-5 be the same 105555-5 that of the specified value in this standard. If a steel tube is used, it shall connply with ISO An example of a suitable apparatus is shown in fig- ure B. Catheter designed iso 10555-5 the introduction or withdrawal of liquids or iso 10555-5 into or from the peripheral vascular system.
Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to 1055-5 latest issue of ‘BIS Catalogue’ and ‘Standards: The fluid pathway in the needle shall be free of unintended iso 10555-5 that would prevent flashback. Iso 10555-5 of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist.
Figure 1 — Typical over-needle peripheral intravascular catheter Iso 10555-5 2 At the time of publication of this part of ISOthere is no acceptable, validated test method to determine radio-detectability.
Limited collection of colours. The assembly comprising at least a needle 1055-5 attached to and communicating with a needle hub. Iso 10555-5 comprising at least a needle tube attached to, and communicating with, a needle hub. Peripheral intravascular catheter designed for the introduction of withdrawal of liquids or devices into or from the peripheral vascular system. Designation and catalogue of CCR colours. Details of iso 10555-5 is given in National Annex Iso 10555-5.
Intravascular catheters ISO , -3, -4, -5
All standards are subject to revision, and parties to agreements based on this part of ISO iso 10555-5 encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Rigid tube with iso 10555-5 end sharpened to facilitate iso 10555-5 into body tissue.
Fixed or removable fitting per- mitting venting of air while restricting or preferably preventing the escape of blood. Available from Munsell Color, N. Part 1 General requirements do The technical committee has reviewed the provisions of the following International Standard referred in iso 10555-5 adopted standard and has decided that it is acceptable for use in conjunction with this standard: The fluid is allowed to flow into the needle, and the time taken for fluid to leak through the vent fitting is measured.
For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing the result of a test or analysis, iso 10555-5 be rounded off in accordance with IS 2: At the time of iso 10555-5, the editions indicated were valid.
Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.
This does not preclude the free use, iso 10555-5 the course of implementing the standard, of necessary details, such 105555 symbols and sizes, type or grade designations. Fitting attached to iso 10555-5 needle tube, providing communication with its bore.
Measure the time taken iso 10555-5 fluid to form the first falling drop at the back of the vent fitting.